Safety Tips to Avoid Electric Shock During Electrical Work

Electrical work does not allow electric shock. However, safety tips are to be kept in mind to avoid it. Electrical professionals face many risks while working with electrical equipment. One of the most severe risks is electric shock. Therefore, safety during electrical work is the most important aspect for the professional as well as the DIY enthusiast. Whether buying from electrical wholesalers in Edmonton or visiting an Edmonton electrical shop, following strict safety measures can prevent accidents and save lives.

Electric Shock Knowledge

An electric shock makes the human body a conductor of electrical current. It can be a slight tingling feeling at low voltages to even fatal injury depending on the voltage and the amount of current running through the body. According to ESFI, more than 30,000 non-fatal electrical shock incidents occur annually in North America.

Safety Tips to Avoid Electric Shock

1. Safety Gear

Protective gears can be worn correctly to minimize electric shock. Among those are:

Insulated Gloves: It protects the hands from being in direct contact with live wires.

Rubber-Soled Shoes: It prevents grounding and minimizes the possibility of the flow of current.

Safety Goggles: It shields the eyes from sparks or debris during electrical work.

2. Switch off the Power Source

Always switch off the power supply before starting to do any kind of electrical work. Test with a voltage tester that the circuit is de-energized. This applies in both domestic and professional workshops supplied by electrical wholesalers in Edmonton.

3. Observe the Wiring Diagram

Reading of a wiring diagram at the onset is essential to fully understand the system of wiring to avoid contact by accident with any live circuit from the wires which carry current.

4. Be Dry

Dont mix water with electricity, work in dry areas and your electrical components moist-free. There are cases, however that will not be avoidable; all this time refer an expert electrician for safety purpose.

5. Insulated Tool

Buy the best quality insulated tools which you can afford from a good Edmonton electrical shop. It will greatly aid in keeping safe from electric shocks since it comprises a nonconductive barrier preventing the electrical current from reaching to you.

6. Use of Ground Fault Circuit Interrupters

GFCIs are significant switches which can prevent you from getting electric shock by cutting power supply once a ground fault has been detected. Install in all areas with moisture, such as in kitchens, bathrooms, and even outside.

7. Avoid Overload of Circuits

Overloading a circuit may lead to overheating, causing fires or electric shock. Balance the electrical loads and use circuit breakers to control appliances with high energy.

8. Avoid Live Wires

Maintain a safe distance from live wires and always ensure they are well-insulated. If working near overhead power lines, position your tools and ladders 10 feet or more away from those lines.

Avoid Common Mistakes

1. Failure to Respect Voltage Ratings

Always look at the voltage rating of the equipment before its use. Applying an equipment rated on a lesser voltage on high-voltage circuits will result in electric shock.

2. Use of Single Visual Inspection

A cable appears to be right but is still not safe with current passing along it. Current safety should, therefore, be tested using a voltage detector.

3. The Use of Broken Equipment

Outdated cords and plugs or faulted tools do raise the rate of getting shock from electricity. Equipped tools from an electrical Edmonton shop should change immediately and always check on what one buys every now and then.

The Function of Electrical Distributors in Edmonton

Electrical wholesalers in Edmonton play an important role in the provision of good quality safety gear and tools. These wholesalers provide a wide range of products including insulated tools, circuit breakers, and PPE among others that are necessary for safe performance of electrical work.

Emergency Procedures on Electric Shock

Steps to take upon experiencing electric shock:

Switch off the electricity supply immediately. It will be an immediate action that will put an end to the flow of electricity.

Do not touch the victim Use a wooden stick as an insulating device to avoid any contact of the victim with the source of electricity.

Dial Emergency Call Immediately call medical care for the victim, irrespective of the appearance of injury on his body.

Administer CPR if Necessary: If the victim is unconscious and not breathing, administer CPR until the emergency professionals arrive.

Safety Awareness End

Safety awareness is a critical factor in the reduction of electric shock incidents. Training sessions and workshops help the electricians and DIY enthusiasts update themselves on the latest safety protocols. Moreover, buying tools and equipment from an electrical shop in Edmonton ensures quality and durability.

Conclusion

Major electrical shock risk demands more serious safety measures if you are doing electrical work. You will reduce the chances of accidents if you follow the following tips and get quality equipment from Edmonton electrical wholesalers or Edmonton electrical shops. Safety is to be taken seriously and good quality of equipment should be ensured while learning to have a safe environment around you.